INFORMATION

 

WHAT IS DIE CASTING

 

COMPARISON OF METALS & MATERIALS

 

GUIDE FOR DIE CASTING DESIGN

 

PROPERTIES

 

HIDDEN COSTS OF OFFSHORE SOURCING

 

 

ALLOYS

Die-casting alloys

Die casting alloys are normally non-ferrous, and there is a large number available with a wide range of physical and mechanical properties covering almost every conceivable application a designer might require.

Aluminum and zinc alloys are the most widely used, and are followed by magnesium, zinc-aluminum (AZ) alloys, copper, tin and lead.

Zinc, lead and tin based alloys are classified as low melting point metals, all melting at less than 725oF (385oC). Zinc-aluminum (ZA) alloys have a slightly higher melting range of 800oF to 900oF (426oC to 482oC). Aluminum and magnesium alloys are considered to be moderate melting point alloys, being cast in the 1150oF to 1300oF (621oC to 704oC) range. Copper alloys are considered to be high melting pint, over 1650oF (899oC). Low melting point alloys are cast in hot chamber machines. Intermediate and high melting point alloys are cast in cold chamber machines. In recent years, specially designed hot chamber machines for die casting magnesium alloys have come into use

Aluminum alloys

Aluminum die casting alloys are lightweight, offer good corrosion resistance, ease of casting, good mechanical properties and dimensional stability.

Although a variety of aluminum alloys made from primary or recycled metal can be die cast, most designers select standard alloys listed below:

360 -- Selected for best corrosion resistance. Special alloys for special applications are available, but their use usually entails significant cost premiums.

380 -- An alloy which provides the best combination of utility and cost.

383 & 384 -- These alloys are a modification of 380. Both provide better die filling, but with a moderate sacrifice in mechanical properties, such as toughness.

390 -- Selected for special applications where high strength, fluidity and wear-resistance/bearing properties are required.

413 (A13) -- Used for maximum pressure tightness and fluidity.

Zinc alloys

Zinc base alloys are the easiest to die cast. Ductility is high and impact strength is excellent, making these alloys suitable for a wide range of products. Zinc alloys can be cast with thin walls and excellent surface smoothness making preparation for plating and painting relatively easy.

It is essential that only high purity (99.99 + 0/0) zinc metal be used in the formulation of alloys. Low limits on lead, tin and cadmium ensure the long-term integrity of the alloy’s strength and dimensional stability.

Zinc-Aluminum ZA alloys

ZA alloys represent a new family of zinc based die casting materials which contain higher aluminum content than standard zinc alloys. These alloys provide high strength characteristics plus high hardness and good bearing properties (Table 2). Thin wall castability characteristics and die life are similar to zinc alloys. ZA-8 is recommended for hot chamber die casting, which ZA-12 and ZA-27 must be cast by the cold chamber die casting process. All ZA alloys offer similar creep properties and are superior to standard zinc alloys.

ZA-8 -- Provides strength, hardness and creep properties.

ZA-12 -- Provides excellent bearing properties with strength and hardness characteristics between ZA-8 and ZA-27, plus good dimensional stability properties and somewhat better castability than ZA-27.

ZA-27 -- Offers the highest mechanical properties of the ZA family and is, therefore, recommended when maximum performance is required.

Magnesium alloys

Magnesium alloys are noted for low weight, high strength to weight ratio, exceptional damping capacity, and ease of machining. Casting temperatures are about the same as aluminum, and both hot chamber and cold chamber machines are used to produce castings.

Casting rates for magnesium are high because of its low heat content which produces rapid solidification. For the same reason, less energy is required to heat the metal to casting temperature.

AZ91HP (high purity) alloy has been developed for die casting parts subject to corrosive environments. Because of lower levels of nickel, iron, copper and silicon versus AZ91B, this alloy is finding applications in automobiles, computers and peripheral equipment, and in other applications where paint or coatings are either undesirable or expensive.

Although magnesium die castings are used uncoated, they can be finished in a variety of ways to give increased protection against corrosion, wear and abrasion resistance, and to improve appearance. Common inorganic treatments include chemical dips, anodizing and plating. Organic coatings -- oil, wax, resin or paint -- are usually applied over chemical treatments or anodizing to seal the surface, increase corrosion protection and provide an attractive appearance.

RELATIVE ALLOY WEIGHTS TO MAGNESIUM

Aluminum

1.6

Zinc

3.7

ZA Alloys

2.7-3.4

Magnesium

1.0

Brass

4.7

Tin

4.0

Lead

6.3

Bronze

4.9

 

 

 

 

 

 

 

Contact Us


2009 West Dartmouth Avenue Englewood, CO 80110
Office: 303-789-4446Fax: 303-789-2647